Jen-Ken AFG 2815 3" Glass/Casting Kiln
$4,289.00Regular price$4,650.00
Save $361.00- 15-day returns
- No sales tax outside Georgia
- Made in USA
Ways to save
Choose your build
Built to order.
Already built, not made to order, so there is nothing else to configure. We confirm the lead time in writing before you are charged.
Lead time 6 to 8 weeks, confirmed in writing before you are charged.
Configure your kiln
Not sure? Call 470-264-3563
-
Orton VentMaster Kiln Vent SystemFan assembly, Collection cup, High-temperature hose, Drill bit, Stud, Printed manual, Orton...

Jen-Ken AFG 2815 3" Glass...
$4,289.00
Overview
Jen-Ken · Glass Kiln · AFG Glass/Casting 3"
Jen-Ken AFG 2815 3" Glass/Casting Kiln
The 2815 3" is the Glass/Casting kiln built for a studio that fires often. Three-inch brick instead of the standard wall — Jen-Ken rates that at roughly 20% more insulation — around a 28-inch shelf with 15 inches of height. It fires top-and-side together for fusing to 1,700°F, and side only for casting and low-fire clay to 2,150°F. Twenty-eight inches is enough for large platters, architectural panels and multi-piece loads, and the heavier brick is what lets you run it hard without punishing the elements. It needs a 45-amp 240V circuit.
FiresGlass, casting, low-fire clay
Max Temp1,700°F / 2,150°F
Chamber28" x 15"
Power240V · 45A
What’s included
The kiln, built and wiredCase, elements, thermocouple, switch box and wiring are all fitted and tested at the factory. It ships crated on a pallet by motor freight.
The controller you orderJen-Ken fits the controller you pick when the order goes in — the AutoFire 12-button, the AutoFire Slide touchscreen or the TAP touchscreen. Each one is a different price, so the controller that ships is the one on your order rather than a fixed model.
Cord and plug — NEMA 6-50PJen-Ken wires the cord and plug at the factory. You supply the matching receptacle on its own circuit — the breaker size and wire gauge for this model are in the specifications below.
Lid lifterJen-Ken's dealer sheet lists this model as including the lid lifter — the spring assist that takes most of the weight out of raising the lid.
2-year limited warrantyJen-Ken's brick-kiln warranty, direct from the factory to the original purchaser.
Not included — kiln furnitureNo shelves, posts or kiln wash in the crate. Jen-Ken prices a furniture kit for this model as a separate line, and we stock the pieces on our accessories pages. Solid-state relays are a paid upgrade rather than standard.
Key features
3-inch brickHeavier insulation than the standard wall — Jen-Ken's own figure is roughly 20% more. It holds a soak better and costs less to run.
Selectable top/side and side firingTop and side together for fusing; side alone for casting, which is how the kiln reaches 2,150°F.
Built to order in FloridaAssembled in Jen-Ken's own Lakeland shop rather than drop-shipped from a distributor.
Chamber size28" x 15" — 5.33 cu ft. That is the space you actually have to load.
Technical specifications
ModelAFG 2815 Glass/Casting 3"
Kiln functionGlass casting, fusing, slumping, low-fire ceramics
Chamber dimensions28" x 15"
Cubic feet5.33 cu ft
Maximum temperature — glass1,700°F (927°C)
Maximum temperature — casting2,150°F (1,177°C)
Firing modesTop/side together for fusing, side only for casting
Brick3-inch
Voltage240V
Amperage45A
Wattage10,800W
PhaseSingle phase
ReceptacleNEMA 6-50R
Breaker (fuse) size50A
Circuit wire gauge#6
Element placementTop/side and side — selectable
ControllerOrton AutoFire 12-button
Kiln weight285 lbs
Estimated shipping weight380 lbs
Shipping dimensions54" x 45" x 43"
Shipping methodMotor freight
Warranty2-year limited (Jen-Ken)
Optional accessories
Kiln shelves, posts and a furniture kitGlass wants a flat, primed shelf and fibre paper; casting wants posts and headroom. Jen-Ken's own shelves and posts are sized to this chamber and we stock them alongside the kiln. Tell us your shelf size and we will match it.
Kiln wash and shelf primerGlass will weld itself to an unprimed shelf. Most glass workers go through primer steadily, so it is worth adding to a first order.
Slumping moulds and fibre paperMoulds and fibre paper are the other half of a warm-glass setup. Tell us the shelf size you are working to and we will point you at what fits.
Controller upgradeJen-Ken fits the Orton AutoFire 12-button as standard and offers the AutoFire Slide touchscreen and the SDS TAP II in its place. It is a factory option rather than a checkout add-on — call us and we will quote it.
Common questions
What does "Glass/Casting" actually mean?Two firing modes in one kiln. For fusing and slumping the elements fire from the top and the sides together, which washes a wide shelf in even heat — that is what flat glass wants, and the ceiling there is 1,700°F. For casting, the side elements do the work on their own and the kiln will go to 2,150°F, which is the range a casting mould and a long ramp need. You select the mode; it is one kiln with two ways of heating, not a compromise between them.
What electrical circuit does it need?240V single phase, a 45-amp draw, 10,800 watts, a NEMA 6-50R receptacle, a 50-amp breaker and #6 copper. That combination matches the wiring table in Jen-Ken's own owner's manual, which gives every 45-amp kiln in their range #6 wire, a 50-amp fuse and a 6-50R, so it is a figure we are happy to print. It is a dedicated run; have a licensed electrician confirm it against local code before delivery.
What cone will it reach?Jen-Ken publishes no cone rating for any kiln in their glass line, this one included, and we have not worked one out from the temperature. What is published is the two ceilings — 1,700°F in glass mode and 2,150°F in casting mode — and those are in the table above. Treat 2,150°F as low-fire clay and glaze territory.
Will it fire clay?Low-fire clay and glaze, yes — Jen-Ken lists low-fire ceramics among this kiln's functions and 2,150°F is in that range. What it will not do is mid-fire or high-fire stoneware: cone 6 is out of reach, let alone cone 10. If pottery is the main event, buy a ceramic kiln and keep this one for glass. If you fire glass most of the time and want the option of a low-fire load, this is exactly the kiln for it.
Is the 3-inch brick worth it?If you fire more than about twice a week, yes. Jen-Ken rates the heavier wall at roughly 20% more insulation, which shows up as a steadier soak, lower running cost and less work for the elements. If you fire occasionally, you are paying for insulation you will not use — the 2415 Glass/Casting is a cheaper kiln on a lighter circuit.
What actually comes in the crate?The section at the top of this page is that list, and it comes from Jen-Ken’s own dealer price sheet for this model rather than from a guess. Kiln furniture is the thing most people assume is in the crate and is not — Jen-Ken prices the shelves and posts as a separate kit. Call or email us if you want the crate confirmed against your build before you order.
How long until it ships?Jen-Ken builds to order in Lakeland, Florida. Their own guidance is that kilns can take several weeks to months depending on the production queue. Call us and we will get you the current estimate before you commit.
Does buying from Peach State Pottery affect my warranty?No. We are an authorized Jen-Ken dealer, so the factory warranty applies exactly as it would buying direct. Jen-Ken gives brick kilns two years. Keep your proof of purchase.
Firing several times a week?
We are authorized Jen-Ken dealers based in Georgia. Tell us what you are making and what power you have available, and we will tell you straight whether this is the right kiln — including when a cheaper one would do.
Talk to an expert →

